Search results for 'hangers and handlebars'
-
Black 12" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$149.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
12" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
12" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn More
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 16" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$149.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
16" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 18" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$149.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
18" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Ape Hangers Fat 1-1/4" diameter Handlebars for Harley-Davidson Motorcycles
$139.99CHROME APEHANGERS
14" Rise 1-1/4" Handlebars
To fit Harley-Davidson motorcycles and custom application.Show chromed!
14" rise. 8.5" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip.
Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley-Davidson
$134.99CHROME APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson motorcycles and custom application.Show chromed!
16" rise. 8.5" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip.
Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 14" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" CHROME APEHANGERS
14" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
14" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" CHROME APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
16" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 18" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" CHROME APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
18" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 18" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"EL DIABLO" BLACK UNIVERSAL APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated black!
18" rise. 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Flat Black
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 12" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" BLACK APEHANGERS
12" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
12" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Pictures curtsey of - shovel1969*64
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" BLACK APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
16" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
16" Ape Hangers 1-1/4" diameter handlebars with Hand Controls for Harley-Davidson
$299.99Chrome 16" Rise Ape Hangers
with Smooth-Contour Control Kit
and Chrome SwitchesThis auction is for complete 1-1/4" handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Made in U.S.A.
Retail $402.99----------------------------------------------------------------
Chrome Apehangers
16" Rise 1-1/4" Handlebars
Show chromed!
16" rise. 8.5" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
XXX Star Nicki Hunter
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
