Dresser Bagger Parts
Items 1 to 24 of 43 total
Grid List
-
Mayhem Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$199.99"MAYHEM" CHROME APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!Triple Plated Chrome!
15" rise. 9" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
39-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finishLearn More -
21" x3.5" Black Mammoth 48 Fat Spokes Front Wheel for Harley-Davidson FL Dual Disc 25MM ABS Bearings Dresser Bagger
$399.0021" x 3.5" Black 48 Fat Spokes Front Wheel
BLACK with BILLET HUB
MAMMOTH 48 SMOOTH SPOKES
To fit any Harley-Davidson Dual Disc models and custom application21" x 3.5" Dual disc front for 25MM axle and ABS Bearings!This is the best spoked wheel you can get. The craftsmanship and quality are surpassed by none. The thick spokes are chromed, Billet hub and rim are powder coated black.Wheel comes with black billet hub and sealed bearings, sealed for TUBELESS applicationSets available
Learn More
-
18" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$555.55Chrome 18" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with just CRUISE and RADIO)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Chrome 'El Diablo' Swedged Apehangers
18" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show chromed!
18" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn More
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
16" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$555.55Chrome 16" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2007
May work on throttle-by-wire models with custom fitting and any custom application
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Chrome 'El Diablo' Swedged Apehangers
16" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show chromed!
16" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$555.55Chrome 14" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Chrome 'El Diablo' Swedged Apehangers
14" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show chromed!
14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
12" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$555.55Chrome 12" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2007
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Chrome 'El Diablo' Swedged Apehangers
12" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show chromed!
14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
12" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$555.55Black 12" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
12" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
12" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles
$555.55Black 14" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome Switches W/ Cruise CrontrolFor Harley-Davidson Touring (Dresser / Bagger) models with Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
14" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
16" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles
$555.55Black 16" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with RADIO and CRUISE ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
16" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
16" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
18" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles
$555.55Black 18" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with RADIO and CRUISE ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
18" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
18" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Clearance Sale! El Diablo Chrome 18" Rise Ape Hangers 1-1/4" Diameter Handlebars Harley Dressers Baggers FLHT FLHTC Motorcycles
$139.00Clearance Sale!Need to make room on shelves. Limited time sale! Get them while they last!"EL DIABLO" CHROME APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
18" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
23" x 3.5" Black 80 Spokes Front Wheel for Harley-Davidson Dual Disc 25MM ABS Bearings
$400.0023" x 3.5" Black 80 Spokes Front Wide Glide Wheel
BLACK with BILLET HUB
Black Rims & Hub, Chrome Spokes
To fit any Harley-Davidson Dual Disc models and custom application23" x 3.5" Dual disc front for 25MM axle and ABS Bearings!This is the best spoked wheel you can get. The craftsmanship and quality are surpassed by none. The spokes are chromed, Billet hub and rim are powder coated black.Wheel comes with black billet hub and sealed bearings, sealed for TUBELESS applicationSets available
Learn More
-
Mayhem Chrome 17" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$199.99"MAYHEM" CHROME APEHANGERS
17" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!Triple Plated Chrome!
17" rise. 9" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
39-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finishLearn More -
Mayhem Chrome 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$199.99"MAYHEM" CHROME APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!Triple Plated Chrome!
16" rise. 9" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
39-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finishLearn More -
23" x 3.5" 80 Spoke Black Billet Hub Front Wide Glide Wheel for Harley Davidson FL Dresser Dual Disc
$400.0023" x 3.5" Black 80 Spokes Front Dual Disc Wide Glide Wheel
CUSTOM HEAVY DUTY 80 SPOKE FRONT WHEEL FOR HARLEY-DAVIDSON.
with BLACK BILLET HUB
23" x 3.5" Rim
To fit 1984 - 2007 Harley-Davidson Dual Disc Wide Glide models and Custom Application.
23" x 3.5"Dual Disc
This is heavy duty, top quality 80 spokes chrome front wheel.
This wheel comes with billet hub, and bearings and center spacers for 3/4" & 1" axles!
Learn More -
4" Harley-Davidson FLH FLT Dresser Road King Exhaust Mufflers Black with Chrome Swiss Cheese Billet Tips
$165.00BLACK CHROME SLIP ON MUFFLERS FOR FLH MODELS
with SWISS CHEESE Billet Tips- Fit 1995 -15 Harley-Davidson touring models FLHR, FLHRC, FLHRS, FLHTCU, FLTR, FLHX ( EXC. 2010 FLHX, FLTRX )
-
Triple plated chrome finish Tips
-
Steady, tough, low rumble
-
Utilize venturi chamber design baffle design to create smoothest power band
-
Race-proven baffle increases torque and horsepower
- Unique internal baffle heat shield design
-
1-3/4" inlets allow for OEM headers and heat shields
-
32" in length
-
Massive 4" outlets on 4" mufflers with chrome billet tips for outstanding look
-
Sold in pairs
Fit 1995 -15 Harley-Davidson touring models FLHR, FLHRC, FLHRS, FLHTCU, FLTR, FLHX ( EXC. 2010 FLHX, FLTRX )
Learn More -
Gas Tank stock Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017 paul yaffe
$179.99Bagger Nation Custom Gas Tank Dash Kit for Touring Models 2008-2016
This kit fits Stock OEM Touring model tanks with round Fuel Pump. NEW Clean And Simple Steel Dresser Dash design is a custom and sick look for all the new 2008-2017 6 gallon HD tanks! When the late model HD Touring gas tank got bigger, so did the OEM dash. So this is a quick and simple way to swap over with two simple mounts to make your stock bulky tank look completely custom and tricked out. This dash is completely metal and can be custom paited to match your bike or chromed out to make it pop. Get your dash kit quick to make your bike bad ass.The dash is a simple, direct bolt on application to your stock tank and really creates a sick look to your tank area!
Tank kit includes a custom low profile steel dash, chrome pop-up gas cap, rubber trim and any necessary mounting brackets.21" between main mounting holes.
22" long2008 - 2017 Harley-Davidson Electra Glide Classic (EFI) - FLHTC
2008 - 2009 Harley-Davidson Electra Glide Standard (EFI) - FLHT
2008 - 2017 Harley-Davidson Electra Glide Ultra Classic (EFI) - FLHTCU
2015 - 2017 Harley-Davidson Electra Glide Ultra Classic Low-FLHTCUL
2010 - 2017 Harley-Davidson Electra Glide Ultra Limited - FLHTK
2015 - 2017 Harley-Davidson Freewheeler-FLRT
2008 - 2009 Harley-Davidson Road Glide (EFI) - FLTR
2010 - 2017 Harley-Davidson Road Glide Custom - FLTRX
2015 - 2017 Harley-DavidsonRoad Glide Custom - FLTRX
2015 - 2017 Harley-DavidsonRoad Glide Special-FLTRXS
2011 - 2013 Harley-Davidson Road Glide Ultra - FLTRU
2008 - 2017 Harley-Davidson Street Glide (EFI) - FLHX
2014 - 2017 Harley-Davidson Street Glide Special - FLHXS
2010 - 2011 Harley-Davidson Street Glide Trike - FLHXXX
2009 - 2017 Harley-Davidson Tri Glide Ultra Classic - FLHTCUTG
2015 - 2017 Harley-Davidson Ultra Limited Low-FLHTKLFits 2008-16 Harley-Davidson Touring FLHT/FLTR models
Will fit Road King 2008-11 models with custom dash modificationsMay custom fit 2003-07 Touring models
Learn More
-
Custom Gas Tank stock oem Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017
$149.99Bagger Nation Custom Gas Tank Dash Kit for Touring Models 2008-2017 for Stock OEM
This kit fits Stock OEM Touring model tanks . NEW Clean And Simple Steel Dresser Dash design is a custom and sick look for all the new 2008-2017 6 gallon HD tanks! When the late model HD Touring gas tank got bigger, so did the OEM dash. So this is a quick and simple way to swap over with two simple mounts to make your stock bulky tank look completely custom and tricked out. This dash is completely metal and can be custom paited , powerdercoated to match your bike or chromed out to make it pop. Get your dash kit quick to make your bike bad ass.The dash is a simple, direct bolt on application to your stock tank and really creates a sick look to your tank area!
Tank kit includes a custom low profile steel dash, chrome pop-up gas cap, rubber trim and any necessary mounting brackets.21" between main mounting holes.
22" long2008 - 2013 Harley-Davidson Electra Glide Classic (EFI) - FLHTC
2008 - 2009 Harley-Davidson Electra Glide Standard (EFI) - FLHT
2008 - 2017 Harley-Davidson Electra Glide Ultra Classic (EFI) - FLHTCU
2015 - 2017 Harley-Davidson Electra Glide Ultra Classic Low-FLHTCUL
2010 - 2017 Harley-Davidson Electra Glide Ultra Limited - FLHTK
2015 - 2017 Harley-Davidson Freewheeler-FLRT
2008 - 2009 Harley-Davidson Road Glide (EFI) - FLTR
2010 - 2013 Harley-Davidson Road Glide Custom - FLTRX
2015 - 2017 Harley-DavidsonRoad Glide Custom - FLTRX
2015 - 2017 Harley-DavidsonRoad Glide Special-FLTRXS
2011 - 2013 Harley-Davidson Road Glide Ultra - FLTRU
2008 - 2017 Harley-Davidson Street Glide (EFI) - FLHX
2014 - 2017 Harley-Davidson Street Glide Special - FLHXS
2010 - 2011 Harley-Davidson Street Glide Trike - FLHXXX
2009 - 2017 Harley-Davidson Tri Glide Ultra Classic - FLHTCUTG
2015 - 2017 Harley-Davidson Ultra Limited Low-FLHTKLFits 2008-16 Harley-Davidson Touring FLHT/FLTR models
Will fit Road King 2008-11 models with custom dash modificationsMay custom fit 2003-07 Touring models
Learn More -
El Diablo Black 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$129.00"EL DIABLO" BLACK APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
15" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 13" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$129.00"EL DIABLO" BLACK APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
13" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$129.00"EL DIABLO" CHROME APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
15" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
12" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$575.55Black 12" Rise 'El Diablo' Ape Hangers
with Black Hand Control Kit
and Black SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are Powder coated Black top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
12" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
12" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Black Switches and Wire Harness
High quality Black switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
13" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles
$575.55Black 14" Rise 'El Diablo' Ape Hangers
with Black Hand Control Kit
and Black SwitchesFor Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are Powder coated Black top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
14" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Black Switches and Wire Harness
High quality Black switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
13" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles
$575.55Black 13" Rise 'El Diablo' Ape Hangers
with Hand Control Kit
and Chrome Switches W/ Cruise CrontrolFor Harley-Davidson Touring (Dresser / Bagger) models with Cruise Control from 1996 to 2012
May work on throttle-by-wire models with custom fitting and any custom application
(Only for models with CRUISE and RADIO ONLY)
This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.11/16" Bore master cylinder. For dual disc application.
with radio controls and cruise controlThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
Black 'El Diablo' Swedged Apehangers
13" Rise 1-1/4" Handlebars for Bagggers/Dressers
Show Black!
13" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
37" wide from tip to tip.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for Dresser hand controls with radio control and cruise control.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
Items 1 to 24 of 43 total
Grid List
