Handlebars
Here you can find 1-1/4'Â phat handlebars for Harley or custom chopper. Demon'â„¢s Cycle offer drag and t-bars in various rise. Our handlebars have accommodations for internal wiring. We also offer apehangers and handlebars for Harley springers. To make your custom project easier please check out handlebars with hand controls. All the installation is done professionally saving you the aggravation of doing internal wiring yourself. Demon'â„¢s Cycle proud to present T-bars with built-in L.E.D. turn signals of our own design. These custom 1-1/4'Â handlebars for Harley-Davidson are available in various rises and in fully wired versions with hand controls installed. Here you will also find custom chrome biller risers for Harley. XX
|
|
How to Install New Handlebar |
-
Black 1-1/4" Drag Handlebars 8" Rise with LED Turn Signals fit Harley-Davidson
$119.99Learn MoreBLACK 8" Rise 1-1/4" T-Bars with Built-In LED Turn SignalsExclusive Demon's Cycle Inc. design gives these drag-bars unique custom look by adding sleek extra bright turn signals with internal wiring.To fit Harley-Davidson motorcycles FLST, FXST, Sportster XL DYNA , LOWRIDER , including Throttle-by-wire models, and any custom application.
Powdercoated BLACK!
8" rise. 3 1/2" Pullback. 6.5" backward sweep. 31" end to end. 1 1/4"-diameter center section tapers to 1" so that standard handlebar controls fit.Come with oversized drilled wiring holes to accommodate any internal wiring. 1/2" Course Thread Riser Holes. Pre-strung for easy internal wire installation. -
Chrome 15" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$109.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback) including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
15" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
.jpg)
Learn More
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Chrome 13" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$109.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback) including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
13" rise. 6" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Chrome 11" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
11" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback) including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
11" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Chrome 9" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
9" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback) including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
9" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$129.00"EL DIABLO" CHROME APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Triple-plated chrome!
15" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Rise Frisco Chubby's Ape Hangers 1-1/4" Diameter Handlebars with Hand Controls and Switches for Harley Motorcycles
$399.99Chrome 14" Rise Frisco Chubby Ape Hangers
with Smooth-Contour Control Kit
and Chrome SwitchesThis listing is for complete 1-1/4" handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Made in U.S.A.
Retail $402.99----------------------------------------------------------------
Chrome Frisco Chubby Apehangers
14" Rise 1-1/4" Handlebars
Show chromed!
14" rise. 6" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
34-1/2" wide from tip to tip. Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
6" Black Z-Bars 1-1/4" Drag Style Handlebars for Harley-Davidson Softail Sportster Dyna
$89.99
Custom 6" 'Z-Bars'
Black HandlebarsThese contemporary designs feature 1-1/4"-diameter 'fat' tubing that is one of
the hot, new custom 'looks' and have holes to accommodate the wiring on
all models from 1982 to present.
They fit the Original Equipment and after-market
risers fitted to most Harley-Davidson models
(except Springer Softail models)
from 1974 to present and Custom Application.34"-wide
6"-rise
3"-pullback
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$129.00"EL DIABLO" BLACK APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
15" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Master Cylinder and Brake Lever Black Hand Control for 1996-10 Dual Disc Harley-Davidson Handlebars
$139.00Black Smooth-Contour Master Cylinder with Brake Lever Assembly
Will fit all dual disc 1996-2010 Harley-Davidson models.
Will also fit 1984 thru 1995 Dual disc models.Will fit 2007-Up models with safety switch.
11/16" Bore master cylinder.This is top quality master cylinder.
Learn More -
Black 1-1/4" Drag Handlebars 6" Rise with LED Turn Signals fit Harley-Davidson
$119.99BLACK 6" Rise 1-1/4" T-Bars with Built-In LED Turn SignalsExclusive Demon's Cycle Inc. design gives these drag-bars unique custom look by adding sleek extra bright turn signals with internal wiring.To fit Harley-Davidson motorcycles FLST, FXST, Sportster XL DYNA , LOWRIDER , including Throttle-by-wire models, and any custom application.Learn More
Powdercoated BLACK!
6" rise. 3 1/2" Pullback. 6.5" backward sweep. 31" end to end. 1 1/4"-diameter center section tapers to 1" so that standard handlebar controls fit.Come with oversized drilled wiring holes to accommodate any internal wiring. 1/2" Course Thread Riser Holes. Pre-strung for easy internal wire installation. -
Black Hand Controls and Switches for Harley-Davidson FLT 1996-2008
$269.99Black Hand Control Kit
Switch housings use Stock HD or CC custom rounded switches.
BETTER LOOK AND BLACK FINISH THEN ANY HD PRODUCT.Will fit all 1996--2008 Harley-Davidson FLT models.
Switch housings with Cruise Control and Radio Control.11/16" Bore master cylinder.This is top quality kit.
Complete Kit Includes: Ergonomic clutch and brake levers, master cylinder, switch housings,switches,wires,
brackets,wire diagram and hardware.Learn More -
Black Hand Controls for 1996-2010 Dual Disc Harley-Davidson Handlebars
$224.99Black Smooth-Contour Hand Control Kit
Switch housings use Stock HD or CC custom rounded switches.
BETTER LOOK AND FINISH THAN ANY HD PRODUCT.
Will fit all dual disc 1996-2010 Harley-Davidson models.
Will also fit 1984 thru 1995 dual disc models with simple rewiring.
It is possible to update most models from 1972 thru 1995 to the latest style with minor wiring and control cable changes.
Will fit 2007-Up models with safety switch. 11/16" Bore master cylinder.This is top quality kit.
Complete Kit Includes: Ergonomic clutch and brake levers, master cylinder, switch housings, brackets and hardware.
Learn More
-
9" Chrome El Diablo Ape Hangers 1-1/4" diameter Internaly Wired with Switches for Harley-Davidson
$274.99Chrome 9" Rise Ape Hangers
Internally Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Chrome Apehangers
9" Rise 1-1/4" Handlebars
Show Chrome!
9" rise. 9" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
16" Chrome El Diablo Ape Hangers 1-1/4" diameter Internally Wired with Switches for Harley-Davidson
$274.99Chrome 16" Rise Ape Hangers
Internally Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Chrome Apehangers
16" Rise 1-1/4" Handlebars
Show Chrome!
16" rise. 9" backward sweep. 1-1/4" diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
18" Chrome El Diablo Ape Hangers 1-1/4" diameter Internaly Wired with Switches for Harley-Davidson
$274.99Chrome 18" Rise Ape Hangers
Internaly Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Chrome Apehangers
18" Rise 1-1/4" Handlebars
Show Chrome!
18" rise. 9" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
12" Chrome El Diablo Ape Hangers 1-1/4" diameter Internally Wired with Switches for Harley-Davidson
$274.99Chrome 12" Rise Ape Hangers
Internally Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Chrome Apehangers
12" Rise 1-1/4" Handlebars
Show Chrome!
12" rise. 9" backward sweep. 1-1/4" diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Master Cylinder and Brake Lever Chrome Hand Control 1996-10 Dual Disc Harley Handlebars
$139.00Chrome Smooth-Contour Master Cylinder with Brake Lever Assembly
Learn More
fit dual disc 1996-2010 Harley, 1984- 995 Dual disc models.
11/16" Bore master cylinder. -
16" Rise Frisco Chubby's Ape Hangers 1-1/4" Diameter Handlebars with Hand Controls and Switches for Harley Motorcycles
$399.99Chrome 16" Rise Frisco Chubby Ape Hangers
with Smooth-Contour Control Kit
and Chrome SwitchesThis listing is for complete 1-1/4" handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Made in U.S.A.
Retail $402.99----------------------------------------------------------------
Chrome Frisco Chubby Apehangers
16" Rise 1-1/4" Handlebars
Show chromed!
16" rise. 6" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
34-1/2" wide from tip to tip. Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Chrome 16" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$109.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
16" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
12" Rise Frisco Chubby's Ape Hangers 1-1/4" Diameter Handlebars with Hand Controls and Switches for Harley Motorcycles
$399.99Chrome 12" Rise Frisco Chubby Ape Hangers
with Smooth-Contour Control Kit
and Chrome SwitchesThis listing is for complete 1-1/4" handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
Unique design has hidden underside mounting
on the switch housings for
an unobstructed smooth, rounded surface on the top housing.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Made in U.S.A.
Retail $402.99----------------------------------------------------------------
Chrome Frisco Chubby Apehangers
12" Rise 1-1/4" Handlebars
Show chromed!
12" rise. 6" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
34-1/2" wide from tip to tip. Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99
210.99
206.99
Professional Installation 235.00
_________________
Total: $1055.97
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 9" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$109.00"EL DIABLO" CHROME UNIVERSAL APEHANGERS
9" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Triple plated chrome!
9" rise. 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.
Chrome finish
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 15" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$129.00"EL DIABLO" CHROME UNIVERSAL APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Triple plated chrome!
15" rise. 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" Inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 11" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$129.00"EL DIABLO" CHROME UNIVERSAL APEHANGERS
11" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Triple plated chrome!
11" rise. 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Chrome 13" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$129.00"EL DIABLO" CHROME UNIVERSAL APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Triple plated chrome!
13" rise. 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Black El Diablo Ape Hangers 1-1/4" diameter Internally Wired with Switches for Harley-Davidson
$274.99Black 14" Rise Ape Hangers
Internally Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Black Apehangers
14" Rise 1-1/4" Handlebars
Flat black!
14" rise. 9" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Cafe Racer Style 4" Black Z-Bars 1-1/4" Drag Handlebars Metric and Sportster Models
$89.99Cafe Racer Style Custom
1-1/4" 'Z-Bars'
Black HandlebarsThese contemporary designs feature 1-1/4" diameter 'fat' tubing that is one of
the hottest and newest custom bars out. Get them now to customize your bike to that one of a kind look. They have holes to accommodate the wiring on
all models from 1982 to present.
They fit the Original Equipment and after-market
risers fitted to Cafe Racer style Metric Bikes and Sportster Models
from 1974 to present and Custom Application.34"-wide
4"-rise
3"-pullback
3 1/2" From Center to Center For Risers.
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 1-1/4" Handlebars Pullback T-Bars 8" Rise with Hand Controls + Switches for Harley-Davidson
$399.99BLACK 8" Rise T-Bars
with Chrome Smooth-Contour Control Kit
and Chrome SwitchesThis auction is for complete 1-1/4" handlebar set-up. Handlebars are powder coated black. All other components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Smooth-Contour Hand Controls
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)
Hydraulic Hand controls also AvailableThis is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Made in U.S.A.
Retail $402.99----------------------------------------------------------------
BLACK 8" Rise 1-1/4" T-Bars
Powder coated black!
8" rise. 3 1/2" Pullback. 1 1/4"-diameter center section tapers to 1" so that standard
handlebar controls fit.
Come with drilled wiring holes.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.*If your motorcycle is equipped with clutch safety switch, state that with your payment and we will include the switch with your order.
Retail $206.99---------------------------------------------------------------
Total package price: 402.99--
210.99--
206.99--
Professional Installation 235.00--
_________________
Total: $1055.97--
Learn More
-
Black 1-1/4" Drag Pullback Handlebars 8" Rise T-Bars fit Harley-Davidson
$84.99
BLACK 8" Rise 1-1/4" T-BarsTo fit All Harley-Davidson motorcycles and Custom Application
Powdercoated BLACK!
8" rise. 3-1/2" Pullback. 6.5" backward sweep. 1-1/4"-diameter center section tapers to 1" so that standard handlebar controls fit.Come with oversized drilled wiring holes to accommodate any internal wiring. 1/2" Coarse Thread Riser Holes. Pre-strung for easy internal wire installation.
Learn More
-
El Diablo Black 15" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$249.99"EL DIABLO" BLACK UNIVERSAL APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated black!
15" rise from Center to Center , 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Flat Black
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 13" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$249.99"EL DIABLO" BLACK UNIVERSAL APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated black!
13" rise from Center to Center , 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Flat Black
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4"-inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Chrome 12" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
12" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Triple plated chrome!
12" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Chrome finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 17" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$119.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
17" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
17" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 15" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
15" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
15" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 13" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$109.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powder Coated!
13" rise.6" backward sweep.1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 11" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
11" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
11" rise. 6" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black 9" Rise Universal Ape Hangers "Frisco" Chubby's 1-1/4" Diameter Handlebars for Harley Motorcycles
$99.99Short-Desc
"CHUBBY FRISCO" BLACK UNIVERSAL APEHANGERS
9" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST, Sportster XL, including Throttle-by-wire models, and any custom application.Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.Black Powdercoated!
9" rise. 6" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 9" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$129.00"EL DIABLO" BLACK UNIVERSAL APEHANGERS
9" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated black!
9" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Flat Black
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
14" Chrome El Diablo Ape Hangers 1-1/4" diameter Internally Wired with Switches for Harley-Davidson
$274.99Chrome 14" Rise Ape Hangers
Internally Wired with Chrome SwitchesThis listing is for 1-1/4" handlebar set-up. All components are top quality parts, featuring hidden mounting wiring and chrome switches.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come professionally assembled, ready to be installed on your motorcycle in minutes.
We did all the hard and tricky work so you can easily install your existing switch housings in minutes or use custom hand controls of your choice.
Here is what you are getting:
Chrome Apehangers
14" Rise 1-1/4" Handlebars
Show Chrome!
14" rise. 9" backward sweep. 1-1/4" diameter. Center section tapers to 1" so that standard handlebar controls fit.
36" wide from tip to tip. Bars are dimpled for late control wiring.
Come with drilled wiring hols.
Retail $210.99--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality USA made chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------
Total package price:
210.99
206.99
Professional Installation 235.00
_________________
Total: $652.98
Learn MoreHow to Install New Handlebar
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1-1/4" inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1-1/4" inch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers were used to mount the new bars.
7. Because the bars are 1" inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch housing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Mayhem Chrome 18" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" CHROME UNIVERSAL APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Chrome black!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!
18" rise from Center to Center, 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Chrome
Learn More
-
Mayhem Chrome 16" Rise Ape Hangers 1-1/4" Handlebars for Harley Motorcycles
$149.99"MAYHEM" CHROME UNIVERSAL APEHANGERS16" Rise 1-1/4" Handlebars
Learn More
To fit Harley-Davidson FLST, FXST and any custom application.
Chrome -
Mayhem Chrome 14" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" CHROME UNIVERSAL APEHANGERS
14" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Chrome finish!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!
14" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Chrome
Learn More -
Mayhem Chrome 13" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" CHROME UNIVERSAL APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Chrome finish!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!
13" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Chrome
Learn More -
Mayhem Black 18" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" BLACK UNIVERSAL APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated semi-gloss black!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!18" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Semi-gloss Black
Learn More -
Mayhem Black 17" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" BLACK UNIVERSAL APEHANGERS
17" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated semi-gloss black!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!17" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Semi-gloss Black
Learn More -
Mayhem Black 14" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"MAYHEM" BLACK UNIVERSAL APEHANGERS
14" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated semi-gloss black!IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!14" rise from Center to Center , 8" backward sweep. 1-1/4" diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2" on-center knurling for firm mounting.
35" wide from tip to tip.
Come with drilled wiring holes.Semi-gloss Black
Learn More -
Mayhem Black 11" Rise Ape Hangers 1-1/4" Handlebars for Harley Road Glide 2016-Up
$195.00"MAYHEM" BLACK APEHANGERS 11" Rise 1-1/4" Handlebars
Fit Harley Road Glide 2016-UpPowder coated blackCome with drilled wiring and mounting holes.Learn More -
Mayhem Chrome 13" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Road Glide 2016-Up
$195.00"MAYHEM" CHROME APEHANGERS
13" Rise 1-1/4" Handlebars
To fit Harley-Davidson Road Glide 2016-UpChrome finishIMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
Our handlebars use one piece technology. There are no joints in 1" to 1.25" transitions. Solid one piece pipe will not fail!
13" rise from Center to Center , 5" backward sweep. 1-1/4" diameter. Handlebar tips taper to 1" so that standard handlebar controls fit.
3-1/4" on-center knurling for firm mounting.
36" wide from tip to tip.
Come with drilled wiring and mounting holes.Chrome
Learn More
Shopping Options
- Category
-
- Grips (32)
- Hand Controls (23)
- Handlebars (181)
- Handlebars with Controls (154)
- Risers (17)
- Brands
-
- Demon's Cycle (423)
- CustomChromeInc (4)
- BDL (1)
- DNA (1)
- Manufacturer
-
- Demon's Cycle (412)
- DNA (1)
- Demon's (3)
- Avon Performance (1)
- Biker's Choice (2)
- Custom Chrome (1)
- Merchants USA (1)
- Kuryakyn (2)
- Santee Fred Kodlin (4)
- demons cycle (4)
- Price
-
- $0.00 - $99.99 (107)
- $100.00 - $199.99 (137)
- $200.00 - $299.99 (56)
- $300.00 - $399.99 (53)
- $400.00 - $499.99 (46)
- $500.00 - $599.99 (31)
- $600.00 and above (2)
You have no items in your shopping cart.
Call us: (954) 943-0000
Mon-Fri 9:00 am - 6:00 pm EST
Sat - 9:00 am - 2:00 pm EST
