Body & Frame
-
Rear Fender for Harley-Davidson FL models 1958-84 with Taillight and Turnsignal Mounts
$109.99Steel Rear Fender
High quality, sturdy, with threaded mounting holes.Rear fender for Harley-Davidson FL models 1958-84 and any Custom Applicationwith taillight and turn signal mounts.33" tip to tip7-3/4" wide
49" over the top
Learn More
-
Smooth FLH Steel Front Fender for Harley-Davidson FLH 1949-1984
$89.99Smooth Style Steel Front Fender
for Harley-Davidson FLH30" long from tip to tip
6-1/2" wide
42" over the top.
7" tall at the mounts
3" distance between mounting holesReinforced steel internal mounting brackets.
Smooth custom style.
A clean mud guard look without blowing the budget. For wideglide application.Learn More
-
Demons outlaw fat tire Bare Steel 5-7/8" Wide Front Fender for Harley Dresser, FLH, Bagger 21" 120 Wheels
$149.99Custom Full Front Fender Fat Tire Conversion
for Harley-Davidson Dresser, Bagger, FLH Models5-7/8" Wide for 120 tire
Designed 21" Wide wheel Wide Glide application
Fits 120 wide tire
Can be custom fit for 19" and 18" wheelsMeasures 5-7/8"+ wide inside6-3/8" between mounting tabs44" long measured with soft tape across top surface
28" long measured tip-to-tip acrossMounting tabs are drilled. 2-3/4" distance between holesFront fender for Harley-Davidson Dresser, Bagger, FLH models and any Custom Application.
Product ID = 447
Learn More -
Bare Steel 5-7/8" Wide Front Fender for Harley 21" 120 Wheels
$155.55Custom Full Front Fender
for Harley-Davidson5-7/8" Wide for 120 tire
Designed 21" Wide wheel Wide Glide application
Fits 120 wide tire
Can be custom fit for 19" and 18" wheelsMeasures 5-7/8"+ wide inside6-3/8" between mounting tabs44" long measured with soft tape across top surface
28" long measured tip-to-tip acrossMounting tabs are drilled. 2-3/4" distance between holesFront fender for Harley-Davidson and any Custom Application
Custom Fender fits all FXST, FXSTC & Dyna Wide Glideand FXWG
perfect for custom bikeProduct ID = 444
Learn More -
Chrome Billet Hand Grips "Black Diamonds" for Harley
$29.99Set of 2 Chrome Billet
"Black Diamonds" Hand Grips
for Harley-DavidsonCNC-machined from 6061-T6 billet aluminum
then triple-chrome-plated. Designed to be a perfect union of form and function.4 diamond shaped rubber ribs, throttle and idle sleeve
Fits all Harley-Davidson models with 1"handlebars from 1973 to present
(except models with handlebar air reservoirs)
Great for Any Custom Application
Learn More -
1-1/4" Handlebars H-Bars 14" Rise with Hand Controls, Switches and Grips for Harley
$289.99Black 14" Rise H-Bars
with Chrome Grips, Chrome Hand Controls Kit
and Chrome Switches Assembledfor Harley-Davidson 1996-Up and Custom Application
This listing is for complete 1-1/4" handlebar set-up. All components are powder coated black or triple plated chrome top quality parts, featuring smooth hand controls, hidden internal wiring, chrome switches and chrome grips.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Chrome Hand Controls with safety neutral switch.
Switch housings use Stock HD or CC custom rounded switches.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
BLACK 14" Rise 1-1/4" H-Bars
Powder coated!
14" rise. 1 1/4"-diameter center section tapers to 1" so that standard
handlebar controls fit. Bars are dimpled for late control wiring.
32" wide
12" pull back3-1/2" distance between mounting bolts
Come with drilled wiring holes.--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------Chrome GripsPerfect bland of custom looks and comfort.
Retail $99.99---------------------------------------------------------------
Total package price:
402.99
210.99
206.99
99.99
Professional Installation 235.00
_________________
Total: $1155.96Fully assembled.
Learn More
-
1-1/4" Black Handlebars X-Bars 7" Rise with Hand Controls, Switches and Grips for Harley
$299.99Black 7" Rise X-Bars
with Chrome Grips, Chrome Hand Controls Kit
and Chrome Switches Assembledfor Harley-Davidson 1996-Up and Custom Application
This listing is for complete 1-1/4" handlebar set-up. All components are powder coated black or triple-plated chrome top quality parts, featuring smooth hand controls, hidden internal wiring, chrome switches and chrome grips.
All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.
Here is what you are getting:
Chrome Hand Controls with safety neutral switch.
Switch housings use Stock HD or CC custom rounded switches.
BETTER LOOK AND CHROME THAN ANY HD PRODUCT.9/16" Bore master cylinder. For Single disc application(Please contact us first if you are looking for a dual disc set-up)This is top quality kit.
Much higher quality than HD or any aftermarket product. Simply the best.
Retail $402.99----------------------------------------------------------------
BLACK 7" Rise 1-1/4" X-Bars
Powder coated!
7" rise. 1 1/4"-diameter center section tapers to 1" so that standard
handlebar controls fit. Bars are dimpled for late control wiring.
32" wide
12" pull back3-1/2" distance between mounting bolts
Come with drilled wiring holes.--------------------------------------------------------------
Chrome Switches and Wire Harness
High quality chrome switches for hand controls.
Wires are soldered and color-coded for easy installation.
Retail $206.99---------------------------------------------------------------Chrome GripsPerfect bland of custom looks and comfort.
Retail $99.99---------------------------------------------------------------
Total package price:
402.99
210.99
206.99
99.99
Professional Installation 235.00
_________________
Total: $1155.96
Fully assembled. 
Learn More -
El Diablo Black 18" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars for Harley Motorcycles
$199.99"EL DIABLO" BLACK UNIVERSAL APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson FLST, FXST and any custom application.Powder coated black!
18" rise. 8" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.Flat Black
Learn More
Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
Black Flat Drag Bonanza V Bars Handlebars Santee by Fred Kodlin fit Harley
$49.99Out of stock
BLACK "BONANZA" V-Bars
To fit Harley-Davidson motorcycles and Custom Application
Santee Designer Series 'Bonanza' Handlebars by Fred KodlinThese are the latest new and improved design Bonanza Bars II from Fred Kodlin of Murdercycles. Designed for use with 96-11 style handlebar controls.Black powder coated!
29" wide.
5" backward sweep.
1"diameter."Flat" style Bonanza custom drag bars.Learn More
-
El Diablo Black 12" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" BLACK APEHANGERS
12" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
12" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Pictures curtsey of - shovel1969*64
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" BLACK APEHANGERS
16" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
16" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
-
El Diablo Black 18" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles
$159.99"EL DIABLO" BLACK APEHANGERS
18" Rise 1-1/4" Handlebars
To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.Powdercoated black!
18" rise. 11" backward sweep.
1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
37" wide from tip to tip.
Come with drilled wiring holes.Black finish
Learn MoreEver notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.- The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are
fabricated from 1 1/4-nch tubing and powder coated black.
2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.
3. The new handlebars have oblong holes to run the control wiring in and out through.
4. air nozzle is used to blow the lead string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.5. The rope was used to pull the controls wire harnesses through the bars.
6. The factory risers wer used to mount the new bars.
7. Because the bars are T inch in diameter at their center mounting position, a stock
clamp was used8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.
9. The switch wiring exits the front of the switch housing and into the bars.
10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars
11. These stunning bars sure remind us of devil wings.
